Bounds to optimal burn‐in and optimal work size

Burn‐in is a widely used method to improve the quality of products or systems after they have been produced. In this paper, we consider the problem of determining the optimal burn‐in time and optimal work size maximizing the long‐run average amount of work saved per time unit in the computer applications. Assuming that the underlying lifetime distribution of the computer has an initially decreasing or/and eventually increasing failure rate function, an upper bound for the optimal burn‐in time is derived for each fixed work size and a uniform (with respect to the burn‐in time) upper bound for the optimal work size is also obtained. Furthermore, it is shown that a non‐trivial lower bound for the optimal burn‐in time can be derived if the underlying lifetime distribution has a large initial failure rate. Copyright © 2005 John Wiley & Sons, Ltd.     

Continuously coupled parametric generators and their quantum statistics

In this paper the quantum-statistical properties of light beams propagating in a directional nonlinear coupler are investigated. This device is composed of a pair of linearly coupled nonlinear waveguides operating by means of degenerate parametric downconversion. The possibility of generation of nonclassical states of light in single and compound modes, using the short-length approximation, is discussed. Influence of linear and nonlinear mismatches for generation of nonclassical light is taken into account. This work was supported by Project LN00A015, Research Project No. CEZ: J14/98 and the COST project OC P11.003 of the Czech Ministry of Education.     

Control of self‐organized low‐dimensional morphology in poly(styrene‐b‐4vinylpyridine)/polystyrene blend thin films

The surface morphologies of poly(styrene‐b‐4vinylpyridine) (PS‐b‐P4VP) diblock copolymer and homopolystyrene (hPS) binary blend thin films were investigated by atomic force microscopy as a function of total volume fraction of PS (?_PS) in the mixture. It was found that when hPS was added into symmetric PS‐b‐P4VP diblock copolymers, the surface morphology of this diblock copolymer was changed to a certain degree. With ?_PS increasing at first, hPS was solubilized into the corresponding domains of block copolymer and formed cylinders. Moreover, the more solubilized the hPS, the more cylinders exist. However, when the limit was reached, excessive hPS tended to separate from the domains independently instead of solubilizing into the corresponding domains any longer, that is, a macrophase separation occurred. A model describing transitions of these morphologies with an increase in ?_PS is proposed. The effect of composition on the phase morphology of blend films when graphite is used as a substrate is also investigated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3496–3504, 2004     

Detection of Pb2+ using a hydrogel swelling microcantilever sensor.

Hydrogels containing benzo-18-crown-6 were used to modify microcantilevers for measurements of the concentration of Pb2+ in aqueous solutions. These microcantilevers undergo bending deflection upon exposure to solutions containing various Pb2+ concentrations as the result of a swelling of the hydrogels. It was found that a concentration of 10(-6) M Pb2+ can be detected using this technology. Other cations, such as Na+, have no effect on the deflection of this cantilever. The cation K+, which also complexes with benzo-18-crown-6, could interfere with Pb2+ detection, but only at high concentrations (> 10(-4) M).     

Electrospinning of ultrafine cellulose acetate fibers: Studies of a new solvent system and deacetylation of ultrafine cellulose acetate fibers

Electrospinning of cellulose acetate (CA) in a new solvent system and the deacetylation of the resulting ultrafine CA fibers were investigated. Ultrafine CA fibers (∼2.3 μm) were successfully prepared via electrospinning of CA in a mixed solvent of acetone/water at water contents of 10–15 wt %, and more ultrafine CA fibers (0.46 μm) were produced under basic pH conditions. Ultrafine cellulose fibers were regenerated from the homogeneous deacetylation of ultrafine CA fibers in KOH/ethanol. It was very rapid and completed within 20 min. The crystal structure, thermal properties, and morphology of ultrafine CA fibers were changed according to the degree of deacetylation, finally to those of pure cellulose, but the nonwoven fibrous mat structure was maintained. The activation energy for the deacetylation of ultrafine CA fibers was 10.3 kcal/mol. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 5–11, 2004     

p型导电掺In的SnO2薄膜的制备及表征

采用溶胶-凝胶提拉法成功地制备了p型导电掺In的SnO2薄膜.x射线衍射测试结果表明，掺In的SnO2薄膜保持SnO2的金红石结构.吸收谱测试结果表明，掺In的SnO2禁带宽度为3.8eV.霍尔测量结果表明，空穴浓度与热处理温度有很大的关系，525℃为最佳热处 理的温度.铟锡原子比在0.05—0.20范围内，空穴的浓度与In的含量有直接的关系，并随In含量的增加而增加. 关键词： SnO2 溶胶-凝胶法 p型导电     

Molecular dynamics simulations of the oligonucleotide with the modified phosphate/phosphonate internucleotide linkage

Impact of the internucleotide linkage modification by inserting a methylene group to the P-O bond (—O—PO ₂ ^— —O— chain changed for —O—PO ₂ ^— —CH₂—O—), on the modified oligonucleotide binding ability to the natural DNA strand was studied by molecular dynamics simulation. Complex of (dT)₁₁ with a deoxyadenosine undecamer containing alternating modified and natural internucleotide linkage was studied as a model system. The Amber force field was completed by a set of new parameters needed to model the modified part of the nucleotide. The simulations confirmed existence of a double-helical complex the melting point of which is considerably higher than 300 K. While the thymidine (unmodified) strand possesses a B-type secondary structure, the conformation of the adenosine (modified) strand is not stable at 300 K. The -ggt conformation of the modified linkages is highly preferred, temporary jumps to the -g-gt and ggt conformations were, however, observed.     

RANDOM EDGE can be exponential on abstract cubes

We prove that RANDOM EDGE, the simplex algorithm that always chooses a random improving edge to proceed on, can take a mildly exponential number of steps in the model of abstract objective functions (introduced by Williamson Hoke [Completely unimodal numberings of a simple polytope, Discrete Appl. Math. 20 (1988) 69-81.] and by Kalai [A simple way to tell a simple polytope from its graph, J. Combin. Theory Ser. A 49(2) (1988) 381-383.] under different names). We define an abstract objective function on the n-dimensional cube for which the algorithm, started at a random vertex, needs at least exp(const·n^1/3) steps with high probability. The best previous lower bound was quadratic. So in order for RANDOM EDGE to succeed in polynomial time, geometry must help.